11/29/2023 0 Comments Cateye velo 7 vs 9Do not concentrate on the computer while riding.The setting method is the same as for "Preparing the computer-4". In the clock mode, press SET button on the back, and the display enters clock setting mode. The setting method is the same as for "Preparing the computer-3". How to change tire sizeĭisplay the Total Distance ( ODO) and press the SET button to change the tire size. * This factor of 0.15 is determined by applying the average value of the overall gasoline-powered passenger cars in 2008 to the equation of the "Carbon offset from 1 km drive of a gasoline-powered car" described on the website of the Ministry of Land, Infrastructure and Transport and Tourism. Trip distance (km) x 0.15 = Carbon offset (kg) The Carbon offset are calculated as follows. This computer measures the calorie consumption by integrating the value calculated from the speed in every second. Press the SET button to confi rm the value. Press and hold the MODE button to move to the next digit. Press the MODE button to increase the value. How to change the total distanceĭisplay DST, and then press the SET button to switch to the total distance manual input screen. *1: When TM exceeds about 27 hours, or DST exceeds 999.99 km. Pressing the MODE button switches the measurement data at the bottom in the order shown in the following figure. When the computer receives a sensor signal, the measuring screen reappears. If the computer has not received a signal for 10 minutes, power-saving screen will activate and only the clock will be displayed. * The total distance ( ODO) is not reset. Pressing and holding MODE on the measuring screen returns the measurement data to 0. Measurements start automatically when the bicycle is in motion. * Generally, the tire size or ETRTO is indicated on the side of the tire. Mark where the valve stem is and measure the distance. Mark the spot on the fl oor and with the rider's weight on the bike, roll exactly one wheel revolution in a straight line (until the valve comes around again to the bottom). With the tires under proper pressure, place the valve stem at the bottom. How to measure the tire circumference (L)įor the most accurate measurement, do a wheel roll out.You can find the tire circumference (L) of your tire size in the chart below, or actually measure the tire circumference (L) of your bicycle. When it is not displayed, check the installation conditions and again. Then, the unit setting is completed, and the unit changes to the Measuring screen.Īfter installed, check that the computer displays the speed by turning the front wheel. Press the SET button with the current clock displayed. Press the SET button to complete setting.Pressing and holding the MODE button switches the display to "Display format", "Hour", and "Minute" in order. * Use "Tire circumference reference table" as a guide. Enter any value of the circumference in cm, and then press the SET button. Pressing the MODE button increases the numeric value flashing, whereas pressing and holding the MODE button moves the digit.With 205 displayed on the screen, press and hold the MODE button.* Entering the tire circumference ensures more accurate measurements. Press and hold to the MODE button with " 205" displayed to change to the wheel size entry screen.ĭetailed setting (enter the numeric value of the tire circumference) * Generally, the tire size is indicated on the side of the tire. Select the tire size (inch) of your bicycle, and then press the SET button. Simple setting (select from the tire size) Set the tire size by either one of the following methods. Press the AC button on the back of the computer. Perform the clear all data operation as shown below, when you use the unit for the fi rst time or restore the unit to the condition checked at the factory. * The magnet may be installed anywhere on the spoke if the above installation conditions are satisfi ed.Īdjust the wire length so that it may not be pulled when the handle is operated. When attaching the FlexTight™ bracket to the handlebar When attaching the FlexTight™ bracket to the stem The FlexTight™ bracket can be attached to either the stem or the handlebar, depending on how the bracket fi ts into the bracket band. Attach the bracket to the stem or handlebar.The clearance between the sensor and magnet is 5 mm (3/16") or less.The magnet passes through the sensor zone.Cateye VELO 9 CC-VL820, VELO 7 CC-VL520 - Cyclocomputer Manual
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |